Noob1903

Thanks bud What would you recommend to boost the plants resistance to PM? Someone mentioned Silicon? If I am planning on using the GH (Now TA) Tripart supplements, is this still required? Do you know where I can buy the other products mentioned? Specifically AQSF? I am based in JHB

Thanks Will try source and use going forward Sent from my iPhone using Tapatalk

Thanks. Is that for use in Veg? Sent from my iPhone using Tapatalk

Thanks for the help, it is seriously appreciated. This grow was looking so good until the PM started. Its still not as bad as it can get (i have been here multiple times) Please can you let me know where to buy and process for treating in veg?

Using Gold Label Hydrococo 60/40 but thinking about changing to Atami Currently use GHE Grow and Bloom but recently changed over to the new 3 part range (Grow, Bloom & Micro)

I haven't tried copper soap yet. Ladies are in Week 3 of flower I have another shed that is for flower. I have 4x 400W HPS lights and the room is bigger. This shed was only ever going to be for Veg I got the globes from ACDC. Not very strong, but do the job for Germination and initial Veg

Thanks, i removed so more leaves when I did a H2O2 drench yesterday Not sure about ratios though. I mixed 14ml per Liter of 50% H2O2 and sprayed yesterday

Tried both variants. Both leave a smell Tried a 4:1 ratio

Bought clones, so don't think its the strains, as far as i know: 3x Apple Pie 3x Banana Kush 3x Gelato 33 3x Zkittelz

Damn, looks great. I would need 2 though, eish

I have read a mountain of info on PM. One of the root problems is too many leaves touching each other and causing air pockets where damp thrives. I have tried to do bit of selective pruning, but have only done that once in Veg and on day 21 of flower. The idea behind the shed was to use it as a veg station so that i could swing them over to the bigger shed to flower. Messed up timing and had to flower in shed 1. Plants are really on top of each other or touching walls etc. Tried the Milk solution, bicarb etc.

extraction at the top, 2 x active intakes below Fans are located above canopy (2x) blowing into canopy (4x) and on the ground (2x)

Thanks. I have a 8" extraction coupled with 6" Carbon filter at the top of the room. I have 2 x 6" duct fans drawing air into the room. Would CO2 not be useless in a traditional grow room as you are venting the CO2 out (via extraction)? I could alter the room design and block off the 2x duct fans and block off the extraction?

Thanks bud I built it during lockdown. Still trying to figure out the correct environment to reduce chances of PM. I run aircon on Dry mode (20 degrees) and small dehumidifier runs continuously. Temps vary about 5 degrees (20 - 16) but will install a panel heater to close that gap. RH is 40 high and 30 low

Some pics of the room and current grow

Thanks My phone died so apologies for not replying Been using H2O2 spray (14ml per Liter of 50%) every time i see any PM and full drench (pull plants outside) every 4 days or so. What preventative measures do you guys take?

Hi Room is 2x2 roughly Room is sealed decently although door let’s a bit of air in, minor though I really went to town with sealing as I was worried about Aphids, Spider mites etc. I think I am not drawing enough air out. I did seal all openings into walls with pantyhose as well as other things. Maybe I’m blocking the outlet? Sent from my iPhone using Tapatalk

Will do, thanks bud Sent from my iPhone using Tapatalk

Tapatalk. Won’t let me upload, I can select Sent from my iPhone using Tapatalk

Sure thing Struggling to upload [emoji2959]

Hi guys Hoping for an opportunity to learn from the gurus! Been growing for a few months. I converted a garden shed into a grow room. Built my new 2nd shed and fitted out the internals after a lot of lessons learnt from mistakes with shed 1. Learning every day but struggling with WPM (I suspect set up issues) New shed: Timber structure Sealed top to bottom Rockwool cavity batts in walls Drywall Chipboard 2x Samsung 220W LED’S 8x LED T5’s 8” Extraction Fan 2x 6” active intake 6” Carbon Filter 4x 300mm Oscillating fans 2x RAM 180mm fans 2x 230mm floor standing oscillating fans 1x Meaco 12L Humidifier 1x Jetair 9000 BTU Aircon I recently messed up timing with a perpetual grow & landed up having to flip to flower in the new shed. Long story short, leaves are all over each other and a most likely cause of the current PM issue (beginning stage) Does anyone have any proven method of 1. Stopping PM in progress. 2, changes they made to the environment to prevent PM? Sorry for the lengthy post Sent from my iPhone using Tapatalk